Understanding the Beko Dishwasher E02 Error Code: E07, E15, and More!

Hello, Beko dishwasher owners! Ever had your Beko dishwasher display the E02 error code and wondered what to do? In this post, we’ll explain what this code means, along with its friends E07 and E15.

We’ll also tackle the mysterious E02 error, its causes, and how to troubleshoot it. Stick around for practical solutions to fix the Beko dishwasher E02 error code. Let’s get started!

Decoding the Beko Dishwasher E02 Error Code: Water Supply Woes Explained!

The Beko dishwasher E02 error code, which may also be displayed as E07 or E15, is typically a signal that there’s a problem with the incoming water supply to the dishwasher. Essentially, it’s telling you there’s a “No Water Error.” This error arises when the dishwasher encounters difficulties in getting the necessary water during its wash or rinse cycles.

In more technical terms, your dishwasher monitors the incoming water through a system called a water liter counter, often referred to as a flowmeter. This flowmeter generates electronic pulses during the “Water Inlet” phase, which occurs at the beginning of any program, including functional tests (commonly known as test mode). If the main board of the dishwasher fails to detect these pulses, it triggers the appliance to display a “Call Service” error, which can manifest as E02, E07, or E15.

The Beko dishwasher E02 error code serves as an indicator that something is amiss with the water supply, prompting you to take action and address the issue to ensure your dishwasher functions properly.

Solving Beko Dishwasher E02 Error code: Troubleshooting and Fixes

Let’s break down the causes and their corresponding solutions for the Beko dishwasher E02 error code:

Causes

1. Closed or frozen water tap

• If the water tap connected to your dishwasher is turned off or frozen, the dishwasher can’t get the water it needs for the cycle.

2. Clogged Water Valve Filter Screen

• The filter screen can become clogged with debris, restricting water flow into the dishwasher.

3. Faulty wire harness connection

• A loose or damaged wire harness connection can disrupt communication within the dishwasher’s components.

4. Faulty Water Inlet Valve

• When the water inlet valve is malfunctioning, it may not open properly to allow water to enter the dishwasher.

5. Faulty Flowmeter

• The flowmeter, which measures water flow, may be defective, leading to inaccurate readings or no water flow detection.

6. Faulty Main Board

• The main board may be malfunctioning, causing errors in communication and operation.

Solutions

1. Ensure the dishwasher tap is open

• Make sure that the water tap for your Beko dishwasher is completely open. This ensures a proper water supply during the cycle.

2. Clean the filter screen

• Remove any debris or material obstructing the filter screen to allow water to flow freely into the dishwasher.

3. Check the wire harness connector

• Inspect the wire harness connections for any loose or damaged wires. Secure or replace as needed.

4. Check water inlet valve resistance

• Use a multimeter to measure the resistance of the water inlet valve. It should fall within the range of 3.8 to 4.2 kiloohms. If it’s outside this range, consider replacing the valve.

5. Check the flowmeter condition

• Ensure the turbine in the flowmeter is functioning correctly.
• Verify the reed switch is working as intended.
• Confirm that the Reed-Switch, aka Reed-Sensor, is receiving 5 Vdc; if not, replace the main PCB (control board).

6. If the error persists, replace the main board

• If none of the above steps resolve the issue, a faulty main control board may be the culprit. Consider replacing it to fix the error.

Conclusion

The E02 error code on your Beko dishwasher can be a minor hiccup with several potential causes, including water supply issues, clogs, and electrical problems.

Clearing Up Confusion: FAQs About Beko Dishwasher E02 Error Code