Electrolux Dishwasher i20 Error Code

In this guide, we’ll explain the Electrolux Dishwasher i20 error code, what it means, why it appears, and the most common causes behind it so you can quickly identify the problem and get your dishwasher back to normal operation.

Electrolux Dishwasher i20 Error Code: Meaning, Causes and fixes

The i20 error code on an Electrolux dishwasher usually appears when there’s an issue with water drainage. This error code is essentially an abbreviation for “Drain Pump,” indicating that the dishwasher is encountering difficulties in expelling water during either the wash or rinse cycle.

To get a bit technical, the i20 error code pops up when the pressure sensor fails to reach its home level within the specified time limit of 90 seconds. This sensor plays a crucial role in monitoring the water level within the appliance, and when it doesn’t reset within the allotted time, it triggers the i20 error, signaling a problem with drainage.

Factors Behind the Electrolux Dishwasher i20 Error Code

Let’s break down each of these contributing factors to the i20 error code on your Electrolux dishwasher:

Solving the Electrolux Dishwasher i20 Error: Step-by-Step Troubleshooting and Repair

Remember to exercise caution and ensure the appliance is disconnected from power before attempting any troubleshooting or repairs.

1. Straighten the drain hose and adjust its height.
   • Inspect the drain hose for any kinks or bends. Straighten it out if necessary.
   • Check the height of the drain hose connection; it should be no more than 60 cm (about 2 feet) above the floor or drain. Adjust it if it’s too high.
   • Reconnect everything securely.
2. Clear Blocked Drain Hydraulic Circuit
   • Turn off and unplug the appliance.
   • Examine the drain pipes, filter, and connections for any obstructions. Remove any debris or foreign objects.
   • Ensure that the drain path is clear and unobstructed.
   • Reassemble and reconnect everything.
3. Check and repair faulty wiring.
   • Inspect the wiring connecting the drain pump to the main control board.
   • Look for loose connections or damaged wires.
   • If you encounter any issues, please address them by repairing or replacing the wiring as necessary.
4. Test and replace a faulty drain pump.
   • Access the drain pump, typically situated at the dishwasher’s lowermost part.
   • To check the resistance of the drain pump, use a multimeter and set the dial to the “ohms” (Ω) setting.
   • Carefully touch the probes of the multimeter to the two terminals of the drain pump.
   • If the dishwasher has a 120-vac drain pump (single phase), the resistance should fall within the range of 15–18 Ω.
   • If the dishwasher has a 220 Vac drain pump (single phase), the resistance should be within the range of 180–230 Ω.
   • For a BLAC drain pump (three-phase), the resistance between the U, V, and W terminals should be approximately 90 Ω.
   • If the resistance measurement is not within the specified range for your drain pump type, it indicates a faulty drain pump, and it should be replaced.

5. Diagnose and replace a faulty pressure sensor.
   • Locate the pressure sensor, often positioned near the bottom of the dishwasher.
   • Inspect the sensor for any damage or loose connections.
   • If it’s found to be malfunctioning, replace it.
6. Address issues with the Main Control Board:
   • First, disconnect the appliance from the power source.
   • Inspect the main control board for visible damage or burned components.
   • If there are signs of a faulty control board, it may need replacement.

Final thought:

The i20 error is often not a serious fault, but it is a clear warning that your dishwasher’s drainage system needs attention. By checking the filter, drain hose, and pump step by step, most users can resolve the issue without calling a technician.